Battery vacuum suction lifter E-Grip, Art. no. 40903

Article no longer available! We recommend the battery vacuum lifter E-Grip Plus art. 40906

Battery vacuum suction lifter E-Grip, item no. 40903

The battery vacuum suction lifter E-Grip is a small and handy suction lifter for lifting all, non-porous materials such as tiles, slabs, glass, ceramics, etc. But it is also possible to lift slightly textured or rough surfaces such as wood, concrete and stone. The suction lifter can lift tiles and slabs weighing up to 100 kg. The diameter of the suction plate measures 20 cm. The operating time with a fully charged battery is 16 h

.

Before using the suction lifter for the first time, you must fully charge the suction lifter (the light indicator will change from red to green). The charging process is only possible with a USB power supply unit (not included). The charging time is 6-8 hours.

CAUTION:

It is not possible to lift wet and slippery tiles or slabs with the vacuum suction lifter, as the rubber on these surfaces cannot suction properly due to the moisture. Make sure that the surface of the area to be vacuumed is clean so that the vacuum lifter can adhere to the material without any problems. The suction lifter should not be used at temperatures below -12 C° and not above 49 C°. 

The scope of delivery at a glance:

• 1x E-Grip suction lifter
• 1x Battery charging cable USB-(without power plug)
• 1x Special cleaning brush
• 1x user manual
• 1x plastic case

Our suction lifter is super easy to use. Simply press the on switch on the side to start the suction process. The vacuum lifter will now suction itself to the desired surface, automatically extracting the air as it does so. When the vacuum pump stops, the suction lifter is ready for use, the maximum suction pressure has been reached. Now you can easily lift the tile. A built-in sensor automatically detects a loss of suction power and activates the pump as needed to maintain constant suction. 

To release the vacuum, simply press the vacuum release lever (on the other side of the on/off switch). The vacuum lifter will now detach from the object without leaving any marks. Do not remove the vacuum lifter until the air has been completely pumped out to prevent uncontrolled detachment.

For larger tiles and slabs, we recommend using 2 suction lifters so you can apply more stability when carrying.

In the sturdy plastic case you also get a USB charging cable type C (without power plug) for charging, an instruction manual, a special cleaning brush and the battery vacuum lifter E-Grip. The average charging time is about 6-8 hours. Next to the on/off switch of the vacuum lifter you will find the charging socket for the charging cable. When charging is complete, a green light will illuminate.

The product should always be cleaned on the underside to ensure optimal adhesion. To clean the suction lifter of superficial dirt on the suction plate, use the supplied cleaning brush or a moistened fiber cloth. Always store the suction lifter in the case to protect it from external influences and to keep the rubber sealing lip clean.

All technical data at a glance:

Article no longer available! We recommend the battery vacuum lifter E-Grip Plus art. 40906

Battery vacuum suction lifter E-Grip, item no. 40903

The battery vacuum suction lifter E-Grip is a small and handy suction lifter for lifting all, non-porous materials such as tiles, slabs, glass, ceramics, etc. But it is also possible to lift slightly textured or rough surfaces such as wood, concrete and stone. The suction lifter can lift tiles and slabs weighing up to 100 kg. The diameter of the suction plate measures 20 cm. The operating time with a fully charged battery is 16 h

.

Before using the suction lifter for the first time, you must fully charge the suction lifter (the light indicator will change from red to green). The charging process is only possible with a USB power supply unit (not included). The charging time is 6-8 hours.

CAUTION:

It is not possible to lift wet and slippery tiles or slabs with the vacuum suction lifter, as the rubber on these surfaces cannot suction properly due to the moisture. Make sure that the surface of the area to be vacuumed is clean so that the vacuum lifter can adhere to the material without any problems. The suction lifter should not be used at temperatures below -12 C° and not above 49 C°. 

The scope of delivery at a glance:

• 1x E-Grip suction lifter
• 1x Battery charging cable USB-(without power plug)
• 1x Special cleaning brush
• 1x user manual
• 1x plastic case

Our suction lifter is super easy to use. Simply press the on switch on the side to start the suction process. The vacuum lifter will now suction itself to the desired surface, automatically extracting the air as it does so. When the vacuum pump stops, the suction lifter is ready for use, the maximum suction pressure has been reached. Now you can easily lift the tile. A built-in sensor automatically detects a loss of suction power and activates the pump as needed to maintain constant suction. 

To release the vacuum, simply press the vacuum release lever (on the other side of the on/off switch). The vacuum lifter will now detach from the object without leaving any marks. Do not remove the vacuum lifter until the air has been completely pumped out to prevent uncontrolled detachment.

For larger tiles and slabs, we recommend using 2 suction lifters so you can apply more stability when carrying.

In the sturdy plastic case you also get a USB charging cable type C (without power plug) for charging, an instruction manual, a special cleaning brush and the battery vacuum lifter E-Grip. The average charging time is about 6-8 hours. Next to the on/off switch of the vacuum lifter you will find the charging socket for the charging cable. When charging is complete, a green light will illuminate.

The product should always be cleaned on the underside to ensure optimal adhesion. To clean the suction lifter of superficial dirt on the suction plate, use the supplied cleaning brush or a moistened fiber cloth. Always store the suction lifter in the case to protect it from external influences and to keep the rubber sealing lip clean.

All technical data at a glance:

• Print this page